Hunterrescue

1. Triumph Xs Devices Driver Ed
2. Triumph Xs Devices Driver Ed
3. Triumph Xs Devices Driver Bluetooth
4. Triumph Xs Devices Driver Wireless

Go to device manager and chose update drivers for Passthru+ XS, chose 'Browse my computer for driver software' ((.)) Than click 'NEXT' it will give you driver warning, press 'Yes', it will open a red windows security about the publisher, just click 'Install this driver software anyway' It will confirm Updated Driver software success. If the issue persists, please follow the steps below to find Hardware Id of the device with missing driver and share it here. Open Device Manager; Expand Other Devices and right click the device with missing driver; Click on Properties - Details - Hardware Id and share it here. Please reply with the findings. Will take it further. Bluetooth® functionality may vary due to hardware and software versions of the Bluetooth devices, individual device settings, phone book size, contact storage method and available memory. Software updates on phones may impact Bluetooth connectivity functionality and performance. Triumph cannot provide any guarantee of complete functionality between a Bluetooth device and the motorcycle. PassThru+ XS USB Driver is a VCI (vehicle communication Interface) enabling you to communicate with the ECU's according to the J2534 specification.

1. If Windows reports 'Unrecognized Device' when tool is plugged: then there is an incompatibility between the tool and the computer. This is normally caused by the USB power source in the computer not supplying sufficient power to the scan tool. The only solution is to place a self powered USB hub between the tool and the computer. This has been seen on some older Dell laptops.

2. Driver Problems

The most common problem is with the USB tool is the USB drivers either not installing properly or having the wrong USB drivers installed for the Windows version used. The first step is to check Device Manager for known USB devices. DO NOT connect the scan tool yet. Note in the figure below the Generic USB Driver circled in yellow. You should see this driver in the USB Serial Bus Controllers of your computer .

Keeping Device Manager open, connect the scan tool with the supplied USB cable . The drivers in the USB Serial Bus Controllers should now include OBDScan OBD-II Interface

If the Generic USB Driver did not show up after the driver installation, and you are running Windows 2000 or XP, then go to the supplied CD and run a file called Install2000.bat. Check Device Manager after running Install2000 and see if the Generic USB Driver is there, it should be, if not please email or call us.

If ‘OBDScan OBD-II Interface’ does not show up then there is a problem with the computer reading the OBDScan tool. One problem we have seen in this area is a ‘weak’ USB power source. The OBDScan tool requires about 150ma, a USB mouse only needs about 50ma. The OBDScan also need the full 5.0v as defined by the USB specification. Some Dell computers did not comply with that specification. What you should do is try putting the OBDScan on a self-powered USB Hub. This will eliminate the computer USB power problems.

AnyTrans not recognizing iPhone, iPad or iPod? This guide offers some basic solutions to help you fix the AnyTrans no device connected problem.

We have received some feedback about AnyTrans not detecting iPhone. Although we are working hard on the development of the new version to fix this, we still deem that it is necessary to compose this Help page for your reference. Frequently asked questions are listed below:

I connected my iPhone using the Apple’s USB cable, and the iMobie program can’t see it. It’s been 10 minutes since I connected it. I also checked my iTunes, and it can recognize it just fine. Can you please help me with it?

Just downloaded your s/w and was instructed to plug in my device. I did so and nothing happened. I also made sure to close iTunes etc. Any suggestions on how to get this going?

Actually, there are quite a few reasons that can cause AnyTrans not recognizing iPhone problem. Here we will tell you why AnyTrans not recognizing your iPhone iPad or iPod and also the solutions.

Part 1. Why AnyTrans Not Recognizing iPhone iPad iPod

1. iTunes is not installed properly.
2. You do not install the latest version of AnyTrans.
3. The anti-virus software is blocking the connection.
4. USB cable problem.

Part 2. How to Fix AnyTrans No Device Connected

Here are some basic tips to fix the AnyTrans not recognizing the iPhone iPad iPod issue.

Triumph Xs Devices Driver Ed

Tip 1. Check the USB. Reconnect your iDevice, and you can try another USB port. Then try a different Apple USB cable.

Tip 2. Restart your iDevice and computer. It’s a very common but practical method for many errors.

Tip 3. Install the latest version of iTunes. iOS devices require Apple Mobile Device Support, which should be automatically installed with iTunes.

Tip 4. Install the latest version of AnyTrans. Go to have a check if you have installed the newest version of AnyTrans.

Tip 5. Trust the computer. Tap Trust on iPhone when it prompts for authorization.

Tip 6. Close anti-virus software temporally.

Tip 7. Update the Apple Mobile Device USB Driver on Windows. The missing or outdated Apple Mobile Device USB driver can cause your iDevice not connecting, so you should update your driver to fix the issue.

To update the driver, you can try Driver Easy, which will automatically recognize your system and find the correct drivers for it. You don’t need to know exactly what system your computer is running, you don’t need to be troubled by the wrong driver you would be downloading, and you don’t need to worry about making a mistake when installing.

You can update your drivers automatically with either the FREE or the Pro version of Driver Easy. But with the Pro version it takes just 2 steps (and you get full support and 30-day refund guarantee):

Step 1. Download and install Driver Easy.

Step 2. Run Driver Easy and click the Scan Now button. Driver Easy will then scan your computer and detect any problem drivers.

Fix AnyTrans No Device Connected

Step 3. Click the Update button next to the flagged Apple Mobile Device USB driver to automatically download the correct version of that driver (you can do this with the FREE version), then manually install it.

Or click Update All to automatically download and install the correct version of all the drivers that are missing or out of date on your system. (This requires the Pro version which comes with full support and 30-day refund guarantee. You’ll be prompted to upgrade when you click Update All.)

Triumph Xs Devices Driver Ed

4) Restart your computer to take effect.

The Bottom Line

Triumph Xs Devices Driver Bluetooth

At last, dear user, if the above suggestions still cannot help, please feel free to contact us by email or leave a comment. It’s our great pleasure to serve you.

Triumph Xs Devices Driver Wireless

Product-related questions? Contact Our Support Team to Get Quick Solution >