Hunterrescue

1. See uninstalling information at the bottom of the page if the driver causes problems for you. Here is an older version of the Mac driver, NOT FOR 10.12 Sierra (V1.0) Download the CH340 Macintosh Signed Driver for Mavericks (10.9), Yosemite (10.10) and El Capitan (10.11).
2. Device manager show only 'USB2.0-Serial' with yellow mark. Then i download ch341 china drivers and install them. That goes ok i click uninstall 'usb2.0-serial driver is uninstalled', then i click install after little time that says drivers are succesfully installed. Then i close that chinese driver window and put my nodemcu back to usb port.

• Winchiphead Driver Download Windows 7
• Winchiphead Driver Download Windows 10

Yota Modems Driver download. Contribute to codebndr/windows-drivers-installer development by creating an account on GitHub. HKLM, SOFTWARE WinChipHead IC CH341PORT, DLL, 0x00010001. Operating System Driver Provider Driver Version; Download Driver: Windows 2000 (32 bit) WinChipHead: 1.3.2014.3 (3/11/2014) Download Driver: Windows XP (32 bit).

CH340 IC is a low cost USB to TTL converter IC. CH340g ICis used in low cost SMD Arduino UNO & Arduino Nano boards. Many USB to Serial converter IC’s are available in the market but this is a low cost IC that is gaining popularity. USB to TTL converter modules are also available based on this IC. Even Node MCU IOT modules also have this IC.

You can download the Drivers for CH340g from below

Winchiphead Driver Download Windows 7

Download CH340g Driver for windows 7, 8 and windows 10

I have personally tested the above CH340 driver on windows 7 and it worked with the Arduino Nano, Node MCU and Arduino UNO clones.

Step By Step Installation of CH340g Drivers

Initially connect your hardware having CH340 USB to Serial IC to your PC. In the device manager it will show “USB2.0-Serial” (as shown in below figure) which means your ch340 driver has not been installed.

Now extract the CH340g drivers in a folder and in that you will find folder named “CH341SER” in which there will be a “setup” application file as shown below.

Winchiphead Driver Download Windows 10

Open the setup file and a “Driver Setup” option will open. Just click on the install file.

This installation takes some time. In my laptop it took 1 minute so just have patience. Once installed it will show driver successfully installed. Now go again back to device manager and there you will see that the driver has been successfully been installed and a com port has been allotted. In below image you can see that “com19” has been allotted for ch340g IC in my laptop

Drivers for the ch340 IC has now been installed successfully. I have tested this drivers and installation process in Windows XP, windows 7. Will test is soon on Windows 8 & windows 10.

You can see in above image that Port Number 19 has been allocated to this IC. If you want you can even change the virtual com port number from Device Manager.

For MAC users you can check CH340 Installation Guide for MAC users

The Prolific Winchiphead CH340 / CH341 / HL340 Serial Driver for AppleMac OS X driver is the reliable interface between your CH340 / CH341 /HL340 based cable and your Mac. Svantek Driver Download for windows. The driver supports many CH340 / CH341 /HL340 based dongles and USB interfaces, like clone Arduino’s.

Features¶

• Winchiphead CH340 / CH341 / HL340-based cables
• Reliable and stable data transfer
• Unix file-descriptor access (/dev/cu.Repleo-CH341-xxx,/dev/tty.Repleo-CH341-xxx)
• Apple’s IOKit implementation
• Baudrates (300, … ,230400)
• Databytes (5, 6, 7, 8)
• Stopbits (1, 2)
• Manual and hardware handshake signal control (RTS, DTR, CTS, DSR, CD,RI)
• Sending break signals (for Cisco routers)
• Compiled for OS X 10.13-I64 (High Sierra), OS X 10.12-I64 (Sierra), OS X 10.11-I64 (El Capitan), OS X 10.10-I64 (Yosemite),OS X 10.9-I64 (Mavericks), OS X 10.8 (Mountain Lion), OS X 10.7 (Lion), OS X 10.6 (Snow Leopard),OS X 10.5-I32 (Leopard), OS X 10.5-PPC (Leopard)